|
database
242 hits for
Model "Panhead" ... (all of these words)
in section "misc" ...
Pages : 1 2 3 [next >>]
|
R 95760-TB |
|
Cam bearing puller - JIMS |
|
usa |
120.00 |
|
R 1001 |
|
Valve guide driver set 5/16" 11/32" 3/8" - JIMS |
|
usa |
24.00 |
|
R 1001-1 |
|
Valve guide driver 3/8" - JIMS |
black |
usa |
14.00 |
|
R 1003 |
|
Rod race remover & installation tool - JIMS |
|
usa |
125.00 |
|
R 1004A |
|
Clutch hub puller tool - JIMS |
|
usa |
60.00 |
|
R 1005 |
|
Main drive gear bushing tool - JIMS |
|
usa |
40.00 |
|
R 1008-TS |
|
Transmission stand (hold in vise) - JIMS |
|
usa |
60.00 |
|
R 1011.36TB |
|
Bushing install.tool for 661-36,660-36 - JIMS |
+ drill |
usa |
34.00 |
|
R 1013.54TB |
|
Bushing inst.tool for 25582-54/73 - JIMS |
+ drill |
usa |
34.00 |
|
R 1018.37TB |
|
Bushing install.tool for 661-36A - JIMS |
+ drill |
usa |
34.00 |
|
R 1023.TL |
|
Transmission race lapping tool, use with - JIMS |
96710TL |
usa |
175.00 |
|
R 1029.TS |
|
Socket for crank pin nut 23966-54A - JIMS |
|
usa |
50.00 |
|
R 1034 |
|
Sprocket shaft holder - JIMS |
|
usa |
70.00 |
|
R 1037.TS |
|
Socket 1-5/16" x 3/4" drive - JIMS |
|
usa |
50.00 |
|
R 1045.TS |
|
Timken bearing remover - JIMS |
|
usa |
140.00 |
|
R 1047.TP |
|
Crank assembly removing tool - JIMS |
|
usa |
125.00 |
|
R 1048 |
|
Hard cap, sprocket shaft protection - JIMS |
|
usa |
25.00 |
|
R 1050 |
|
Transmission stud installer tool - JIMS |
|
usa |
35.00 |
|
R 1052 |
|
Snap ring installer oil pump - JIMS |
|
usa |
45.00 |
|
R 1053 |
|
Oil pump seal installer - JIMS |
|
usa |
50.00 |
|
R 1056 |
|
Top dead center piston stop - JIMS |
|
usa |
12.00 |
|
R 1059 |
|
Spoke wrench |
|
usa |
7.00 |
|
R 1060 |
|
Valve spring seat cutter - JIMS |
|
usa |
80.00 |
|
R 1062 |
|
Arbor, valve spring seat cutter - JIMS |
|
usa |
17.50 |
|
R 1064 |
|
Valve guide cutter - JIMS |
|
usa |
90.00 |
|
R 1066 |
|
Cam installation tool - JIMS |
|
usa |
40.00 |
|
R 1080 |
|
Solid brass hammer - JIMS |
|
usa |
35.00 |
|
R 1085-FP |
|
Lapping compound - JIMS |
|
usa |
12.00 |
|
R 1086-FP |
|
Lapping compound - JIMS |
|
usa |
12.00 |
|
R 1090 |
|
Mini valve spring tester - JIMS |
|
usa |
175.00 |
|
R 1097 |
|
Replacement drill - JIMS |
|
usa |
4.00 |
|
R 1110 |
|
Pinion gear gauge pin set - JIMS |
|
usa |
20.00 |
|
15-0028 |
|
Valve spring kit, with collars & keepers |
|
usa |
55.00 |
|
162A |
|
Cups, top springs (2) |
chrome |
usa |
30.00 |
|
162B |
|
Cups, bottom springs (2) |
chrome |
usa |
30.00 |
|
R 1725 |
|
Steering head bearing race installer - JIMS |
|
usa |
40.00 |
|
R 2043 |
|
Fork tube plug socket - JIMS |
|
usa |
36.00 |
|
R 2044 |
|
39mm Slider and cap kit - JIMS |
|
usa |
80.00 |
|
R 2045 |
|
Fork seal installation tool 35mm slider - JIMS |
|
usa |
40.00 |
|
R 2046 |
|
Fork seal installation tool 39mm slider - JIMS |
|
usa |
40.00 |
|
R 2047 |
|
Fork seal installation tool 41mm slider - JIMS |
|
usa |
40.00 |
|
R 2048 |
|
Delrin cap for sliders - JIMS |
|
usa |
40.00 |
 |
C 2085-2 |
|
Seat post bushing installation tool |
|
usa |
35.00 |
 |
C 2086-1 |
|
Seat post bushing installation tool |
|
usa |
10.50 |
 |
C 2097-2 |
1523-36 / 30011-36
|
Generator screw kit, with Phillips head |
chrome |
usa |
7.50 |
 |
C 2098-2 |
1523-36 / 30011-36
|
Generator screw kit, with Phillips head |
cad |
usa |
5.00 |
 |
C 2099-16 |
057 / 2329
|
Lifter base screw kit, with Phillips heads and lockwashers |
chrome |
usa |
10.00 |
 |
C 2100-16 |
057 / 2329
|
Lifter base screw kit, with Phillips heads and lockwashers |
cad |
usa |
9.50 |
 |
C 2103-13 |
|
Transmission top cover screw kit, with Phillips heads |
chrome |
usa |
17.00 |
 |
C 2104-13 |
|
Transmission top cover screw kit, with Phillips heads |
cad |
usa |
12.25 |
 |
C 2108-12 |
|
Headlamp bracket mounting kit |
|
usa |
25.00 |
 |
C 2143-2 |
14007-45/45643-45
|
Springer spring rod bushings '46-'57 |
park |
usa |
31.00 |
 |
C 2186-11 |
|
Front crashbar mounting kit - bolts, nuts, washers |
chrome |
usa |
6.00 |
 |
C 2187-11 |
|
Front crashbar mounting kit - bolts, nuts, washers |
cad |
usa |
5.75 |
|
R 2188 |
|
Cam bearing installer - JIMS |
|
usa |
100.00 |
|
R 2232 |
|
Steering head bearing race remover - JIMS |
|
usa |
50.00 |
|
R 2233 |
|
Tappet oil screen plug tool - JIMS |
|
usa |
17.00 |
|
R 2234 |
|
Primary locking tool - JIMS |
black de |
usa |
33.00 |
|
R 2237 |
|
Pinion gear lock tool - JIMS |
|
usa |
95.00 |
|
R 2244 |
|
Top fork nut socket - JIMS |
|
usa |
45.00 |
|
R 2245 |
|
Clutch lock plate - JIMS |
|
usa |
60.00 |
|
R 2249 |
|
Cam bearing gauge set - JIMS |
|
usa |
50.00 |
|
R 2265 |
|
Socket 1-3/16" x 1/2" drive - JIMS |
|
usa |
55.00 |
|
R 2281 |
|
Cam bushing puller - JIMS |
|
usa |
115.00 |
 |
C 2282-1 |
|
Tap 11/16"-16 Oversize timing plug, oil tank drain plug |
|
usa |
27.00 |
|
R 2316 |
|
Primary locking bar - JIMS |
|
usa |
19.00 |
 |
C 2318-1 |
|
Tool - sprocket shaft bearing retainer |
|
usa |
50.00 |
|
R 2338 |
|
Breather valve gear, oversize +.030" - JIMS |
|
usa |
65.00 |
|
R 2338S |
|
Breather valve gear, standard - JIMS |
|
usa |
65.00 |
|
M 3118PG |
|
Pitch gauge UNF-UNC |
|
usa |
8.00 |
|
M 3606TS |
|
Tap & Die set 41-Piece |
|
usa |
165.00 |
 |
L 522 |
|
Panhead service manual |
|
usa |
17.00 |
 |
L 533 |
|
Shop dope, volume IV |
|
usa |
20.00 |
|
H 5407-2 |
|
Heli-coil thread repair kit 1/8"-27 NPT |
|
|
140.00 |
|
H 5521-1 |
|
Heli-Coil kit 12-24 |
|
usa |
38.00 |
|
H 5521-2 |
|
Heli-Coil kit 8-32 |
|
usa |
38.00 |
|
H 5521-3 |
|
Heli-Coil kit 10-24 |
|
usa |
38.00 |
|
H 5521-4 |
|
Heli-Coil kit 1/4"-20 |
|
usa |
30.00 |
|
H 5521-5 |
|
Heli-Coil kit 5/16"-18 |
|
usa |
32.00 |
|
H 5521-6 |
|
Heli-Coil kit 3/8"-16 |
|
usa |
33.00 |
|
H 5521-7 |
|
Heli-Coil kit 7/16"-14 |
|
usa |
35.00 |
|
H 5521-8-2 |
|
Heli-Coil kit 1/2"-13 special |
|
usa |
48.00 |
|
H 5523-14 |
|
Heli-Coil kit 14 mm spark plugs |
|
usa |
125.00 |
|
H 5528-3 |
|
Heli-Coil kit 10-32 thread |
|
usa |
38.00 |
|
H 5528-4 |
|
Heli-Coil kit 1/4"-28 thread |
|
usa |
48.00 |
|
H 5528-5 |
|
Heli-Coil kit 5/16"-24 thread |
|
usa |
48.00 |
|
H 5528-6 |
|
Heli-Coil kit 3/8"-24 thread |
|
usa |
45.00 |
|
H 5528-7 |
|
Heli-Coil kit 7/16"-20 thread |
|
usa |
48.00 |
|
H 5528-8-2 |
|
Heli-Coil kit 1/2"-20 special |
|
usa |
60.00 |
|
H 5540-4 |
|
Heli-Coil kit 1/4"-24 special |
|
usa |
63.00 |
|
H 5540-6 |
|
Heli-Coil kit 3/8"-20 brake drum |
|
usa |
68.00 |
 |
L 556 |
|
Accessory catalog '57 |
|
usa |
11.00 |
 |
L 557 |
|
Accessory catalog '60 |
|
usa |
11.00 |
 |
L 565A |
|
Riders handbook '55 Panhead |
|
usa |
11.00 |
 |
L 565B |
|
Riders handbook '58-'64 Panhead |
|
usa |
11.00 |
 |
L 565C |
|
Riders handbook '50 Panhead |
|
usa |
11.00 |
|
L 593 |
|
1951 Cross-index |
|
|
18.00 |
 |
L 625 |
|
How to restore your H-D |
|
usa |
35.00 |
 |
C 7017-16 |
|
Cylinder base nut set hi-crown |
acorn |
usa |
12.50 |
 |
C 7100-13 |
|
Oil pump plug and nut set |
acorn |
usa |
11.50 |
Pages : 1 2 3 [next >>]
Note: Ohio residents add applicable sales tax.
generator, timer, starter, spark coil, spark plugs, ignition
chains, sprockets, transmission, clutch
exhaust systems
axles, brakes, rims, spokes, forks, steering dampers, stands, footboards, seat post, shock absorbers, luggage carrier, ride control, handlebars, windshields, chain guards, fenders, legshields, tanks, oil/gas lines
all
engine, oil pumps etc.
common screws, nuts, washers, rivets, bearings, rollers, wire terminals, clips, clamps, retaining rings, o-rings, grommets, oil seals
miscellaneous
batteries, speedometers, lamps, instrument panel, switches, electrical, sidecar, tools
inlet pipes, carburetor, air cleaner
About the part numbers:
The number in the "Order #"-column is the number we need if you want to order the part.
The number in the "OEM #"-column is the "Original Equipment Manufacturer" number, the original part number.
From the Order number you can tell if it is an original or repro part: If the number begins with a letter it is a repro part. (usually a R for parts, an L for books, C for Colony kits, etc.)
Many items are listed without a price, this means they are in stock but you will have to ask for a price quote.
|